ELPRO 105U

The ELPRO 105 range of telemetry modules provide remote monitoring and control by radio or twisted-pair wire, over short or long distances. Transducer signals connected at one module (input signals) are transmitted to another module where the signals are re-created as output signals, or passed via RS232/485 to a host device such as a PLC or SCADA system. More Info

Industrial Wireless Ethernet Plug & Work with ELPRO 905U-E

The 905U-E is an ideal solution for Ethernet connections in process control and 
automation applications - PLC%u2019s, DCS, SCADA, data acquisition, wireless video 
%u2026 the 905U-E can handle multiple applications simultaneously. More Info

905U-G Wireless Gateway

Wireless connectivity between different data buses - Profibus, Ethernet, Modbus, DF1, DeviceNet, Modbus Plus  
Interface between Wireless I/O and DCS/PLC/HMI 
Wireless isolation firewall for data bus extension More Info

Wireless Profibus DP ELPRO 905U-G-PR

Wireless Profibus DP interface, to 12Mbit/sec Uses 900MHz license-free radio band Up to 20 miles line-of-sight, 3000 feet in congested industrial environments More Info

ELPRO 905U-K

The 905U-K wireless I/O module is an economical solution for the remote monitoring of process signals. The 905U-K connects to discrete, pulse or analog signals from process transducers, and transmits these signal values by radio. The 905U-K is suitable for alarm or metering applications, as well as general plant monitoring. More Info

ELPRO 905U

The ELPRO 905U range of wireless I/O provides a low cost alternative to expensive signal wire 
installations, over short or long distances. Transducer and control signals connected at one 
module (input signals) are transmitted to other modules where the signals are re-created as 
output signals, or passed via a data bus to a host device such as a PLC, DCS or SCADA system. More Info

105U-G Wireless Gateway

The 105U-G Wireless gateway products provide a Wireless interface between various data buses used in process and automation applications. The 105U-G includes an integral radio transceiver, and transfers transducer and control signals (I/O) using a highly secure and highly reliable radio protocol. More Info

ELPRO 405U

The ELPRO 405U radio modem module provides RS232 or RS485 connections by radio. It can be used instead of serial cable to link PLC 2019s, dataloggers, supervisory computers and intelligent transducers. More Info

ELPRO 505U-K

The 505U-K wireless I/O module is an economical solution for the remote monitoring of process signals. The 505U-K connects to discrete, pulse or analogue signals from process transducers, and transmits these signal values by radio. The 505U-K is suitable for alarm or metering applications, as well as general plant monitoring. More Info

DEMO-905

The DEMO-905 has been designed to demonstrate the 905U telemetry modules in a customer 
environment. This is a fully working demonstration that simulates radio control of a tank system. More Info

YU6/900

The YU6/900 6 element Yagi antenna is made for use with the ELPRO 900 series telemetry products. The cc10/900 AND CC20/900 coaxial extender kits are suitable for use with the YU6/900 More Info

YU16/900

The YU16/900 16 element Yagi antenna is made for use with the ELPRO 900 series telemetry 
products. The YU16/900 is suitable for use when extended coaxial cable run are encountered with 
9db loss or greater. The antenna is designed for pole mount clear from obstructions. More Info

Antenna SG900EL

The SG900EL collinear antenna may be used for external or internal mounting. Designed for use with the ELPRO 900 series range of telemetry products the SG900EL meets specific radio conditions for these products. The SG900EL is a slimline, lightweight antenna that is easily mounted. More Info

Antenna CFD890EL

The CFD890EL ground independent half wave dipole may be used for external or internal mounting. Designed for use with the ELPRO 900 series range of telemetry products the CFD890EL meets specific radio requirements for these products. The CFD890EL is a slimline, lightweight antenna that is easily mounted. More Info

WH900

The WH900 whip antenna is made for use with the ELPRO DEMO-905 demonstration sets. This antenna is small measuring only 3.5" or 90mm in length. More Info

CC900TAIL

The CC900TAIL is a 24201D (800mm) RG58 coaxial lead. The tail is terminated with a SMA (male) connector for module connection and a flanged N-Type (female) bulkhead connector. More Info

CC10/900 and CC20/900

The ELPRO antenna coaxial extender kits are designed for use with the ELPRO 900 series telemetry modules.The CC10/900 is approximately 33 long (10m) and the CC20/900 is approximately 66%u2019 (20m) long. More Info

SER905

The SER905 serial configuration lead is ideal for programming the ELPRO 900 series modules. 
Molded D9 (9 pin) connectors provide a strong and durable lead. More Info

Bracket Yagi Kit

The Yagi antenna requires a single mounting bracket. The bracket assembly consists of 1xU-Bolt xD-plate with nuts and washers. The brackets are zinc plated mild steel. More Info

BR COLLINEAR KIT

The Collinear antenna requires two mounting brackets to hold the antenna in position. The bracket assemblies consist of 1xU-Bolt 3xD-plates with nuts and washers in each set. The brackets are zinc plated mild steel. More Info

Emergency Shower & Eyewash Stations

SITUATION 
A worker in an industrial plant is sprayed with a harmful liquid. He follows procedures; manages to reach and activate an emergency shower; but then collapses. He is the only person aware of the situation ...until found some time later. More Info

Converting 16 bit unsigned integers to a Floating Point Number For Allen-Bradley SLC500 PLC

The purpose of this document is to provide RS Logix programming code for SLC-500 PLC%u2019s to 
purposefully understand an analogue input variable, that using a 105U, 105S-1, 2 or a 905U, 
905S-1, 2 analogue input, radio linked to a 105U-G- (DF1) or 905U-G-(DF1) then to serial 
connection to SLC-500 using the DF1 protocol. More Info

Communications between Profibus DP Slave Wireless Gateway (105U-G / 905U-G) and Siemens S7300 PLC 2019s

The purpose of this document is to illustrate an application setup using a Siemens S7 2013300 PLC communicating via Profibus to an Elpro 105U/905U-G-PR1 module. All references in this document to the 905U-G also apply to the 105U-G. More Info

905G DeviceNet Application Note

The following document details the connection of a 905U-G-DE1 (DeviceNet Slave) to a Rockwell 
Automation SLC 5/04 PLC and 1747-SDN Scanner. The document outlines the software 
configuration procedure for both ELPRO and Rockwell Automation equipment, but does not detail 
hardware installation. For hardware installation instructions consult the appropriate ELPRO or 
Rockwell user manuals. More Info

DG900

The DG900 whip antenna is made for use with the ELPRO 900 series telemetry products. The DG900 is fitted with approx 17. 2019 / 5m mini coaxial cable and SMA male connector. Further coaxial extensions are not recommended with this antenna. More Info

ELPRO 505U

The 505U radio telemetry module is an economical solution for the remote monitoring of process signals. The 505U can connect to digital, pulse or analogue signals from process transducers, and transmit these signal values by radio. The 505U is suitable for alarm or metering applications, as well as general plant monitoring. More Info

SG900-6

The SG900-6 collinear antenna is designed for use with the ELPRO 900 series range of telemetry products. The SG900-6 meets specific radio requirements for these products and is a slimline, lightweight antenna which is easily mounted More Info

Communications between DF1 Wireless Gateway (105U-G / 905U-G) and Allen-Bradley PLC 19s

The purpose of this document is to show the application of using DF1 communications with the 
105U/905U-G-MD1 module. 
All references in this document to the 905U-G also apply to the 105U-G. More Info